OpenEBS

Overview

OpenEBS (Elastic Block Store) is an open-source platform that enables cloud-native, local or distributed persistent volume (PV) storage for Kubernetes. It is a platform-agnostic alternative to Amazon Elastic Block Store.

For more about OpenEBS, see the official OpenEBS documentation, particularly the Prerequisites.

Planning your deployment

There are multiple storage engines to provision local as well as replicated volumes in OpenEBS based on the use case:

1. Local volumes (Local PV device, LVM local PV)
2. cStor replicated volumes (not recommended, see warning)

Before installing, consider the following pros and cons of each solution.

Local PV device volumes

This is Aerospike's recommended storage solution for OpenEBS.

Pros:

• Dynamic volume provisioner as opposed to a static provisioner.
• Better management of the block devices used for creating local PVs by OpenEBS NDM. NDM provides capabilities like discovering block device properties, setting up Device Filters, metrics collection and ability to detect if the block devices have moved across nodes.

Cons:

• Local PV size cannot be increased dynamically.
• Enforced capacity and PVC resource quotas on the local disks or host paths.
• A 1-1 mapping between the physical disk attached to the Kubernetes node and PVs claimed by the Aerospike pod (or any application) running on that node, which restricts the maximum number of PVCs that can be created on a Kubernetes node.

LVM local PVs

Pros:

• Solves all aforementioned limitations of the local PV device.
• Aerospike can create any number of PVCs (aggregate size should be less than the size of the volume group)

Cons:

• All worker nodes need to have lvm2 installed. This involves another step to create a volume group on each Kubernetes node before installing the OpenEBS lvm CSI driver.
• The backup/restore and clone features are not supported in this.
• During cluster scaleup, the volume group must already be created on the upcoming node.

cStor replicated volumes (not recommended)

Although it is possible to use replicated local volumes, Aerospike strongly discourages doing so.

• Aerospike already implements replication at the application level, and the additional replication could severely impact performance and reliability.
• cStor has an iSCSI layer to provision volumes, which impedes performance.

Local PV device setup

The OpenEBS dynamic local PV provisioner can create Kubernetes local persistent volumes using block devices available on the node to persist data.

1. Set up OpenEBS

Install OpenEBS on the cluster using kubectl.

kubectl apply -f https://openebs.github.io/charts/openebs-operator.yaml

This creates pods in the openebs namespace. A deamonset then runs NDM (Node Disk Manager) pods on each Kubernetes node. NDM pods detect attached block devices and load them as block device custom resources into Kubernetes.

note

Use OpenEBS as the only provisioner in the cluster. If your cluster is using additional provisioners along with OpenEBS like gce-pd (Google Compute Engine Persistent Disk), use exclude filters in your openebs-operator.yaml file to prevent those disks from being consumed by OpenEBS.

For more information on filtering, see NDM Filters.

Without exclude filters in a cluster with additional provisioners, this error appears:

Unable to mount pvc <pvc-name>, mount point is busy

Restart all NDM pods on each node after modifying the configuration.

2. Install Aerospike cluster

Use the value openebs-device for the storageClass key to provision a local volume PVC.

    volumes:
      - name: workdir
        aerospike:
          path: /opt/aerospike
        source:
          persistentVolume:
            storageClass: ssd
            volumeMode: Filesystem
            size: 1Gi
      - name: ns1
        aerospike:
          path: /test/dev/xvdf1
        source:
          persistentVolume:
            storageClass: openebs-device
            volumeMode: Block
            size: 5Gi

OpenEBS then creates BlockDeviceClaim objects to claim the already created BlockDevices.

Run get BlockDeviceClaim, get pv,get pvc, and get pod to check that the objects have been successfully created.

Set up an LVM local PV

note

Before beginning, all nodes must have lvm2 utilities installed.

1. Set up Kubernetes nodes and volume group

Use vgcreate to set up a volume group that will be used by the LVM Driver for provisioning the volumes.

This example creates two volumes, then groups them into the lvmvg volume group.

sudo pvcreate /dev/sdb1
  Physical volume "/dev/sdb1" successfully created.
sudo pvcreate /dev/sdc1
  Physical volume "/dev/sdc1" successfully created.
sudo vgcreate lvmvg /dev/sdb1 /dev/sdc1
  Volume group "lvmvg" successfully created

2. Install OpenEBS LVM driver

Install the latest release of the OpenEBS LVM driver by running the following command.

kubectl apply -f https://openebs.github.io/charts/lvm-operator.yaml

Run get pods to see one lvm-controller pod and lvm-node daemonset running on the nodes. You may see more pods depending on your setup.

kubectl get pods -n kube-system -l role=openebs-lvm
NAME                       READY   STATUS    RESTARTS   AGE
openebs-lvm-controller-0   5/5     Running   0          80s
openebs-lvm-node-jtb9l     2/2     Running   0          73s
openebs-lvm-node-ppt8f     2/2     Running   0          73s
openebs-lvm-node-ssgln     2/2     Running   0          73s

3. Install storage class

Create a storage class with the provisioner field set to local.csi.openebs.io.

apiVersion: storage.k8s.io/v1
kind: StorageClass
metadata:
  name: openebs-lvmpv
parameters:
  storage: "lvm"
  volgroup: "lvmvg"
provisioner: local.csi.openebs.io
volumeBindingMode: WaitForFirstConsumer

4. Install Aerospike cluster

Install an Aerospike cluster by setting storageClass to openebs-<your volume group name> to provision a local volume PVC.

    volumes:
      - name: workdir
        aerospike:
          path: /opt/aerospike
        source:
          persistentVolume:
            storageClass: ssd
            volumeMode: Filesystem
            size: 1Gi
      - name: ns1
        aerospike:
          path: /test/dev/xvdf1
        source:
          persistentVolume:
            storageClass: openebs-lvmpv
            volumeMode: Block
            size: 5Gi

Verify Aerospike pods and PVC with get pv,get pvc, and get pod to check that the objects have been successfully created.